Painting furniture is actually a very critical process, it not only directly affects the quality of the furniture, but also affects the appearance of the furniture. Therefore, most furniture factories have to go through several inspection procedures for this process alone. Next, Cheap Hotel Furniture Manufacturer will introduce the specific process of furniture paint.
1. Furniture sand inspection is the prelude to the entire paint quality. The quality of sand inspection directly affects the quality of the entire product, and it is also one of the indispensable procedures in the paint workshop. Before the product is inspected for sand, it is necessary to inspect the previous process of the product. Scrape the place where the texture is relatively deep, have small missing corners or some small peelings, and then use a flat sander to apply 240 #Sand paper for grinding, some products can not be machine-operated by hand or self-made tools for grinding. After grinding, use 400# sandpaper for secondary grinding until it meets the quality acceptance standard of this process.
2. The purpose of furniture polishing is to better show the texture and texture of the material, to properly correct the color difference of the material, and to improve the color repair efficiency. The process of wiping requires the operator to be able to accurately distinguish different color differences. If there is a large color difference, it needs to be re-colored or toned until the colors match. But it should be noted that each product must be thoroughly wiped off the floating color in the process of wiping, so as not to cause color difference between products. For the furniture that needs to be painted, do the basic treatment before painting. Use coarse to fine sandpaper to repeatedly polish the surface of the furniture to make the surface of the furniture smoother;
3. The purpose of furniture spray primer is to increase the thickness of the furniture paint film and improve the flatness in the next process operation. Usually in the furniture industry, the fully enclosed type is the most widely used. The fully enclosed type is normally sprayed with primer three times, but each time it requires the next process to grind. From paint deployment to spraying, the quality requirements are very high. Generally, the first coating is not too thick during the operation, but the subsequent coatings should increase with the number of spraying passes, each time It is necessary to spray evenly without sagging. Spray primer on polished and smooth furniture surfaces
4. The quality requirements of the furniture oil mill are very high. The effect of the oil mill directly affects the quality of the next steps. The oil mill is also the process that has the most problems in the furniture paint production process. Apply water-based wood putty to furniture to get a better hand feeling. Batch insert head, second putty, insert large holes and deep recesses on the surface before applying putty.
5. The biggest effect of furniture color repair on products is to make the color of each product consistent. It is generally appropriate to spray four times on flat work products (such as countertops, facades, etc.). The color requirements of the side and the front should be the same. For products (such as dining chairs, cabinets) that are not easy to be sprayed, spray the products on the opposite side. After the spraying operation of each product is completed, the color palette must be compared, and the color can be handed over after the same color. Carry out the bottom coloring treatment on the furniture to get the desired color;
6. The spray finish of furniture is the last process in the paint making process and the last process in the entire furniture making process. The quality of face oil spraying mainly has the following two factors, environmental factors and human factors. Environmental factors refer to that the environmental sanitation in the spray booth is not clean enough to cause too many particles after the paint is dried, and the hand feels bad. Human factors refer to uneven, sagging, and rough parts of the paint surface that have not been sprayed in place.
1. Furniture sand inspection is the prelude to the entire paint quality. The quality of sand inspection directly affects the quality of the entire product, and it is also one of the indispensable procedures in the paint workshop. Before the product is inspected for sand, it is necessary to inspect the previous process of the product. Scrape the place where the texture is relatively deep, have small missing corners or some small peelings, and then use a flat sander to apply 240 #Sand paper for grinding, some products can not be machine-operated by hand or self-made tools for grinding. After grinding, use 400# sandpaper for secondary grinding until it meets the quality acceptance standard of this process.
2. The purpose of furniture polishing is to better show the texture and texture of the material, to properly correct the color difference of the material, and to improve the color repair efficiency. The process of wiping requires the operator to be able to accurately distinguish different color differences. If there is a large color difference, it needs to be re-colored or toned until the colors match. But it should be noted that each product must be thoroughly wiped off the floating color in the process of wiping, so as not to cause color difference between products. For the furniture that needs to be painted, do the basic treatment before painting. Use coarse to fine sandpaper to repeatedly polish the surface of the furniture to make the surface of the furniture smoother;
3. The purpose of furniture spray primer is to increase the thickness of the furniture paint film and improve the flatness in the next process operation. Usually in the furniture industry, the fully enclosed type is the most widely used. The fully enclosed type is normally sprayed with primer three times, but each time it requires the next process to grind. From paint deployment to spraying, the quality requirements are very high. Generally, the first coating is not too thick during the operation, but the subsequent coatings should increase with the number of spraying passes, each time It is necessary to spray evenly without sagging. Spray primer on polished and smooth furniture surfaces
4. The quality requirements of the furniture oil mill are very high. The effect of the oil mill directly affects the quality of the next steps. The oil mill is also the process that has the most problems in the furniture paint production process. Apply water-based wood putty to furniture to get a better hand feeling. Batch insert head, second putty, insert large holes and deep recesses on the surface before applying putty.
5. The biggest effect of furniture color repair on products is to make the color of each product consistent. It is generally appropriate to spray four times on flat work products (such as countertops, facades, etc.). The color requirements of the side and the front should be the same. For products (such as dining chairs, cabinets) that are not easy to be sprayed, spray the products on the opposite side. After the spraying operation of each product is completed, the color palette must be compared, and the color can be handed over after the same color. Carry out the bottom coloring treatment on the furniture to get the desired color;
6. The spray finish of furniture is the last process in the paint making process and the last process in the entire furniture making process. The quality of face oil spraying mainly has the following two factors, environmental factors and human factors. Environmental factors refer to that the environmental sanitation in the spray booth is not clean enough to cause too many particles after the paint is dried, and the hand feels bad. Human factors refer to uneven, sagging, and rough parts of the paint surface that have not been sprayed in place.
コメント